[. . . ] Operating Instructions Diamante G 2150 To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M. -Nr. 51 3 IMPORTANT SAFETY INSTRUCTIONS When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Electrical Safety ~ Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. Consult a qualified electrician if in doubt. ~ Before installation or service, The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance. Keep these operating instructions in a safe place and pass them on to any future user. [. . . ] The "Start/Stop" indicator flashes and the indicator of the last set program lights. Starting a program ^ Select the desired program with the program selector button. The indicators "Start/Stop", "Rinse" and the last selected program light. Otherwise important program steps could be interrupted. Selecting a program Choose your program according to the type of load and soiling. The "Program guide" describes the programs and use. Program sequence display After a program has been started the current stage of the program is indicated by the program cycle indicator. 26 Program guide Program When to use Prerinse 1 2 Program sequence Main wash Interim rinse 1 2 Final rinse Drying Pots & Pans For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent dose Run-time 125 min For normally soiled dishware Run-time 129 min For normally soiled dishware, energy saving program with a long soaking time and a low temperature Run-time 95 min Extended wash time, for sanitizing normally soiled dishware with dried on food Run-time 115 min "Quick program" for lightly soiled dishware, e. g. party dishware includes sensor controlled Glasscare, not suitable for detergent tabs Run-time 30 min To rinse dishes when a complete program is not needed detergent is not recommended Run-time 13 min x x x x x Normal Economy x x x x x x x x x x SaniWash x x x x x Short x x x Rinse & Hold x Usage: Electric: 0. 01 - 1. 23 kWh Water: 1. 3 - 6. 3 gal (5 - 24 l) 27 Use At the end of a program When the program has finished the "End" indicator lights. The dishwasher continues to use electricity until turned off with the s button. vacationing, turn off the water supply. Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. , Open the door with care. Close the door firmly until it clicks into place. Changing a program If the detergent flap is already open do not change the program. If a program has already started and you wish to change it: ^ Press the "Start/Stop" button for at least one second. ^ Select and start the desired program. 28 Additional functions Factory default All settings can be reset to the factory default. ^ Press the "Start/Stop" button and at the same time turn the dishwasher on s. Hold the "Start/Stop" button until the "Start/Stop" indicator comes on. The bottom program indicator flashes once long and twice short in intervals. ­ The "Rinse" indicator flashes: All settings are the factory default. ­ The "Rinse" indicator is off: At least one setting was changed. ^ To reset the dishwasher to the default settings, press the "Start/Stop" button. ^ Turn the dishwasher off s. 29 Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue The Start/Stop indicator does not flash after the dishwasher is turned on with s. The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. Make sure it is a 15 A breaker. The fuse has tripped. The drain pump is running when the door is open. There may be a technical ­ Turn the dishwasher off fault. ­ Call Miele Technical Service. 30 Frequently asked questions Problems water intake/drain Issue The "Intake/Drain" indicator flashes and lights alternately. [. . . ] The manufacturer cannot be held responsible for unauthorized work. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. [. . . ]